This refrigerator starts out as a block of wood, just about anything will do. I think I used pine 2 x 4's. For the body cut a piece 5" tall x 2 7/8" deep x 2 3/8" wide. If you have to stack and glue to get your size that's all right. If you have an old refrigerator to copy and measure, that's great, use it. Refrigerators will vary a little on measurements. I know the old ones were smaller than today's refrigerators.
The door is 3 5/16" tall x 2 3/8" wide and 1/4" thick. I used basswood.
The drawer is 1 1/4" tall x 2 3/8" wide and 1/4" thick. I used basswood.
The bottom grille is 3/8" tall x 2 3/8" wide and 3/16" thick. I used basswood.
You will need some basswood 1/32" thick for the gasket and bottom and 1/16" thick for the back grille.
Once you have gotten all of your pieces cut to size make a pattern to use for the top of the body. If you have access to a band saw or scroll saw use it to round off the corners on the top of the refrigerator. If not get some 100 grit sandpaper and sand the corners off. Soften the front and back edges just a bit. Don't keep them sharp.
**Important** Please dry fit your pieces to your pattern to keep the rounding off from going to far. Dry fit your pieces together while you are sanding to make sure they will fit . You want a space between the door and drawer about card stock thickness. A little more between the drawer and bottom grille. The bottom grille should be even with the bottom of the body. Adjust your pieces now before the painting and gluing.
After you are happy with the body match the door to it. With sand paper, maybe 220 grit, round the face of the door. Soften the edge that will be towards the body, leave the outside and inside bottoms alone. Keep these sharp.
Go onto the drawer. Keep the inside and outside bottom and the top edges sharp. Round the face to the sides just as you did with the door.
I copied a refrigerator that had a round center pull on the drawer. I used my Dremel to cut into the basswood. I used an engraver cutter. Unfortunately, I couldn't undercut the center circle enough. When trying I just kept making the center smaller and I thought I should stop while I was ahead. Thinking about it now I should have taken the center out and replaced it with a dowel that had a small circle glued to it. You can do either.
The bottom grille is sanded just like the drawer. I glued on 3 pieces of half round to make it look like a grille. You can make half round from 1/16" x 1/16" basswood strips, sand 2 corners round on one side. Glue these evenly spaced onto the front of the grille. Round them off towards the sides.
Use Rustoleum white and black for the painting. The grille will be painted black, the rest is white. Give everything 2 coats, let the paint dry between coats.
Now sand, using 220 grit. The body is going to take longer if you used pine or even if you stacked basswood. You will have to paint and sand to cover the grain and where the pieces were glued together. We are painting a couple of coats then sanding to a smooth finish. It will take a few days to do this. As you start getting a smooth finish start using a finer grit sandpaper, up to 300 or 400 grit. You are after a smooth porcelain appliance finish. You stop when you are satisfied, do not sand the final coat.
While you are painting and sanding you can make the back grille, gasket, and bottom.
Trace around the back of the body onto card stock. Measure in 3/32" to 1/18" around to top and sides. Cut out and place onto back of body. If you need to change the size do it now, you should have not more that 1/18" of the body showing.
When you like the size, trace onto 1/16" thick basswood and cut out. Remember to cut on the line or your piece will be bigger than you expect. Dry fit this, if it's the right size paint it black.
Trace around the bottom of the body onto card stock. This piece's edges are even the the body. Trace onto 1/32" thick basswood. Dry fit and trim if needed. Paint black.
Trace around the door onto card stock. Measure in a 1/16" around the top and sides. Cut out and place against the door. We want this gasket to be just inside the door, not too far in, enough to see that it's just a bit smaller. When you are happy with that, trace onto 1/32" thick basswood and cut out. Dry fit, make changes if needed. Mix your Rustoleum white and black to make grey and paint the gasket.
I used Testor's silver enamel to paint a line on the bottom of door and top of drawer, around the circle and the knob of the drawer. I used masking tape to do the lines.
I use wood glue to glue the parts together.
Glue the bottom onto body, keep the edges even.
Glue the back grille onto back of body. Make sure you have an even margin of body showing on sides and top.
Glue gasket onto front of body. Keep an even margin of body showing around top and sides.
Glue on door, drawer and bottom grille. The bottom grille is even the the body, not the bottom piece you glued on.
For the handle I used 1/16" thick basswood. I traced a circle 1/4" round. I cut this in two so each piece was 1/4" x 1/8". The next piece is 7/8" long from 1/16" thick basswood. One end is cut just like the 2 other pieces (1/4" x 1/8") to fit between them. The other end is long and straight for the handle pull. I have a diagram at the top of the page. Glue these 3 pieces together. Sand round the end of the handle pull tip. Paint this silver. You will have to do this a few times with a little sanding between coats to get a smooth aluminum finish.
I used super glue to attach the handle, be careful.
If you have any questions about this project, please e-mail me and I will be glad to help you.
Kris
No comments:
Post a Comment